Hallo zusammen,
hat jemand von Euch einen Postprozessor für die Beamicon Basic/ Vcarve Kombination, die mit einer vierten Achse funktioniert?
Finde leider keinen!
Viele Grüße 🖖
Postprozessor 4. Achse Vcarve + Beamicon Basic
-
-
Wenn du nur Trommelgravieren willst, kann das Beamicon2 auch ohne PP mit der 4. Achse.
-
https://docs.vectric.com/docs/…cessor-editing/index.html
Da steht doch alles, was man wissen muss. Da kannst ihn dir doch schnell mal anpassen und testen.
-
Danke! Habe ich ausprobiert und bekomme jetzt den "Wrap" hin. Allerdings passen die Dimensionen so gar nicht mehr. Ein 2,5 cm Durchmesser wird ca. um das 100-fache größerer angezeigt in Beamicon.
Hat da jemand eine Idee?
So sieht der PP nun aus:+================================================
+
+ Beamicon2 - Vectric machine output configuration file
+
+================================================
+
+ History
+
+ Who When What
+ ======== ========== ===========================
+ Mark 02/08/2013 Written
+ Mark 13/09/2021 Added post revision for V11
+ XXX 18/03/2022 Rotary PP
+================================================
POST_NAME = "Beamicon2 (ROTARY_ mm)(*.din)"
FILE_EXTENSION = "din"
UNITS = "MM"
ROTARY_WRAP_Y = A
+------------------------------------------------
+ Line terminating characters
+------------------------------------------------
LINE_ENDING = "[13][10]"
+------------------------------------------------
+ Block numbering
+------------------------------------------------
LINE_NUMBER_START = 0
LINE_NUMBER_INCREMENT = 10
LINE_NUMBER_MAXIMUM = 999999
+================================================
+
+ Formating for variables
+
+================================================
VAR LINE_NUMBER = [N|A|N|1.0]
VAR SPINDLE_SPEED = [S|A|S|1.0]
VAR FEED_RATE = [F|C| F|1.1]
VAR X_POSITION = [X|C| X|1.3]
VAR Y_POSITION = [Y|C| Y|1.3]
VAR Z_POSITION = [Z|C| Z|1.3]
VAR ARC_CENTRE_I_INC_POSITION = [I|A| I|1.3]
VAR ARC_CENTRE_J_INC_POSITION = [J|A| J|1.3]
VAR X_HOME_POSITION = [XH|A| X|1.3]
VAR Y_HOME_POSITION = [YH|A| Y|1.3]
VAR Z_HOME_POSITION = [ZH|A| Z|1.3]
VAR SAFE_Z_HEIGHT = [SAFEZ|A| Z|1.3]
VAR WRAP_DIAMETER = [WRAP_DIA|A||1.3]
+================================================
+
+ Block definitions for toolpath output
+
+================================================
+---------------------------------------------------
+ Commands output at the start of the file
+---------------------------------------------------
begin HEADER
"%"
"[N] (VECTRIC POST REVISION)"
"[N] ([REVISION])"
"[N] G64 P0.02"
"[N] G21"
"[N] G17"
"[N] G90"
"[N] G0[ZH]"
"[N] M6 T[T]"
"[N] G43H[T]"
"[N] M3 [S]"
+---------------------------------------------------
+ Commands output for rapid moves
+---------------------------------------------------
begin RAPID_MOVE
"[N] G0[X][Y][Z]"
+---------------------------------------------------
+ Commands output for the first feed rate move
+---------------------------------------------------
begin FIRST_FEED_MOVE
"[N] G1[X][Y][Z][F]"
+---------------------------------------------------
+ Commands output for feed rate moves
+---------------------------------------------------
begin FEED_MOVE
"[N] G1[X][Y][Z]"
+---------------------------------------------------
+ Commands output for the first clockwise arc move
+---------------------------------------------------
begin FIRST_CW_ARC_MOVE
"[N] G2[X][Y][I][J][F]"
+---------------------------------------------------
+ Commands output for clockwise arc move
+---------------------------------------------------
begin CW_ARC_MOVE
"[N] G2[X][Y][I][J]"
+---------------------------------------------------
+ Commands output for the first counterclockwise arc move
+---------------------------------------------------
begin FIRST_CCW_ARC_MOVE
"[N] G3[X][Y][I][J][F]"
+---------------------------------------------------
+ Commands output for counterclockwise arc move
+---------------------------------------------------
begin CCW_ARC_MOVE
"[N] G3[X][Y][I][J]"
+---------------------------------------------------
+ Commands output at toolchange
+---------------------------------------------------
begin TOOLCHANGE
"[N] G17"
"[N] G90"
"[N] M5"
"[N] G0[ZH]"
"[N] M6 T[T]"
"[N] G43H[T]"
+---------------------------------------------------
+ Commands output for a new segment - toolpath
+ with same toolnumber but maybe different feedrates
+---------------------------------------------------
begin NEW_SEGMENT
"[N] [S] M3"
+---------------------------------------------------
+ Commands output at the end of the file
+---------------------------------------------------
begin FOOTER
"[N] M5"
"[N] G0[ZH]"
"[N] G0[XH][YH]"
"[N] M30"
"%"
-
Du musst den gleichen Offset für die A Achse im CAD/CAM benutzen, wie in der Beamicon. Sonst stimmt der Durchmesser ja nicht...
Jetzt mitmachen!
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!
